|
|
|
|
|
|
Laser lens was changed to 1.5inch (Spot Diameter: 100µm)!
What's FabLab?
|
At FPGA-CAFE/FabLab Tsukuba, you can use all tools free when you agree that must open every information of tools, ideas, design, process, and what you build using by these tools under the open source license (ex.Creative Commons, BSD License, etc.). And, you must pay some supplies cost for use. It is better that you prepare some extra materials for prepareing to fault design, miss-operation, or the other mistakes. We planning to sell some materials and supplies. Please care yourself from harming you when using tools. IN NO EVENT SHALL THIS SHOP OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. (It from BSD License with a little change.) |
| This project is supported with ILC at University of Tsukuba and funding from JST (Japan Science and Technology Agency) . Contact us: susu@fpgacafe.com |
Current Tools
| Tools | Products | Main Use |
Supplies (You must pay) |
Data Format (You must prepare) |
|---|---|---|---|---|
| Laser Cutters | EPILOG Mini24-60W | Acrylic Cutting and Engraving | - |
CorelDRAW(.cdr), or Illustrator(.ai), or DXF |
| Working area: W610xD305(xH203)mm, Max Cutting Thickness: Acrylic 13mm? | ||||
| Circuit Board Prototyping Machines | MITS Eleven Auto (PDF) | Prototyping 1-layer circuit boards | Milling bits and Drills | RS274X and DrillData |
|
Working area: W320xD220(xH45)mm, Minimum pattern/milling width: 0.2mm, Drill Lineup: 0.8, 1.0, and 3.0mm |
||||
| N2 Reflow Ovens | CIF FT-05 ANBE SMT Co. Custom Model | Soldring |
Solder paste, N2 gas (if you need) |
Solder and Heat Profile |
| Working area: W400xD350mm, N2 gas: Normal density or G3-Class | ||||
| Soldering Irons | HAKKO FX-950 | Soldering | Solder wire | - |
| Oscilloscopes | Tektronix TDS-2014 100MHz 1GS/s 4ch , KENWOOD CS-5135 40MHz Analog | Electric signal observation | - | - |
| RC-Oscillators | KIKUSUI 418B | Low frequency signal generation | - | - |
|
Output frequency:10Hz-1MHz(3%+1Hz), Amplitude: sin wave 7Vrms(Min) / square wave 16Vp-p(Min), Output Impedance:600Ω |
||||
| DC Power Supplies | KIKUSUI PMC35-1A DC35V, 1A(Max) | Power source | - | - |
| Multimeters | SANWA ED-570C | Measurement Voltage, Current, Resistance, etc. | - | - |
| FPGA Programmers | TOKUDEN J-Writer | XILINX, ALTERA and LATTICE's FPGA/CPLD JTAG Programming | - | each bit files |
| Support Devices: XILINX XC95/95XL,CoolRunner2,XC18V,XCF00S/XCF00P,Spartan2/2E,Spartan3/3E/3A/3AN/3ADSP,Spartan6,Virtex2/2Pro,Virtex4,Virtex5, ALTERA MAX2, Cyclone, Cyclone2,Cyclone3, FLEX10K,ACEX1K, ArriaGX, and LATTICE XP2. | ||||
| XILINX DLC-9 | XILINX FPGA/CPLD Programming | - | each bit files | |
| Support Devices: XILINX All FPGA/CPLDs | ||||
| Coffee Mills | Kalita Dia-mill | coffee beans grinding | - | a favorite grain |
You can use a nipper, needle-nose plier, tweezers, screwdriver, and etc.
Back to home
Switch to Japanese.
(C)2010 SUSUBOX Project. All Rights Reserved.